Most of the time, people are looking forward to picking up their cars from the detailers. They are too excited to finally see that new-like shine on their cars. But how do you maintain this shine?
Think about what that front end sees in a week: gravel on Deerfoot, a salty brine coating from November on, and a Chinook that swings the temperature 20 degrees by supper. Quality PPF in Calgary handles all of that for years, but it needs a bit of looking after too. Skip that, and the gloss fades, the edges collect dirt, and the topcoat has a harder time healing marks.
So here’s what we’d do if it were our own car, plus what to check when something looks off.
Before anything else, consider how long ago it was installed. If it’s under two weeks, put the hose down. The film needs 7 to 14 days before its first wash, because the adhesive is still settling and a little moisture is still working its way out from underneath. That means no automatic car washes and no pressure wands either. They can catch an edge that hasn’t stuck down properly yet.
Once you’re past that point, you’ll need a few things. One bucket and an old sponge won’t do the job on film. And if you’re going to spend a little extra anywhere, make it the towels, because coarse ones leave fine marks you won’t notice until the sun hits the hood at the wrong angle.
Grab the hose and rinse the whole car before you touch it with anything. You’re getting the mud and that dried winter brine off first, so your mitt isn’t dragging grit across the film. Point the spray along panel edges, not straight into them. This is the step most people rush. This is also the one step that counts when the car’s caked in brine. Give it a few minutes.
Next, fill one bucket with shampoo and the other with plain water. Start on the roof and work down, one panel at a time. After each panel, dunk the mitt in the plain water and rub it against the grit guard before you go back for more soap. It may sound fussy but this is what keeps the grit on the bottom of the bucket instead of back on your paint. Leave the lower doors and rocker panels for last. They’re the grimiest, and you don’t want that dirt anywhere near the rest of the car.
Do you use a pressure washer? If so, stay 12 to 18 inches back. This goes for any XPEL Calgary installation. A ruler is 12 inches, so picture one between the nozzle and the panel. Aim straight at the panel, at 90 degrees, especially around seams. Come in at a shallow angle and you can push water right under an edge, which is usually where lifting starts.
Dont let the car air-dry. Calgary water is hard, so every drop that evaporates leaves a little mineral spot behind, even if it looks almost clear. Blot it first, or wipe lightly with a clean microfibre towel. If you have an air blower, use it around the badges and mirror caps too where water likes to hide
Discove the right order for car detailing in Calgary.
Ever spotted a bird dropping on the hood a couple of days too late? We’ve all done it. Sap, bug splatter and tar work the same way. The heat bakes them on, and they get harder to lift every day. So deal with them when you see them.
Skip harsh industrial solvents and abrasive compounds. They can cloud the topcoat. If a spot won’t come off, resist the urge to scrub. Soak it again and give it a few more minutes.
Have you thought about a ceramic coating over your XPEL Paint Protection Film? It’s worth a look. The surface gets more hydrophobic, so salt and slush rinse off easier, and your washes go quicker. Just have a shop apply it, and wait until the film has fully cured first. Not sure whether yours has? Ask your installer.
What shouldn’t go on it? Traditional waxes, especially petroleum-based ones. Aggressive polishing pads and rotary buffers can haze or discolor clear film, so they are out too.
Notice an edge lifting or a bubble? Your first instinct will be to press it down or pick at it. But don’t do that. Pulling it or trimming it yourself lets more grit in and can tear the film. Call your installer instead to fix the small lifts. It’s also worth walking around the car after a big Chinook thaw and checking the hood line and fender seams. Those fast temperature swings put stress on the edges.
Found a few light scratches? Don’t panic yet. Modern urethane film usually heals light swirls with a bit of heat. Park the car in direct sun for a while, or pour warm water over the spot (warm, not hot), then look again after a sunny afternoon. If a scratch has cut through the topcoat, though, it won’t heal. You will need professional help to take care of it then.
Learn the common mistakes to avoid when applying a PPF in Calgary.
So what actually matters most? The two most important things to remember are: wait out the curing window, and never put a dry or dirty mitt on the film. Most of the rest follows from those. These two rules are what keep your PPF in Calgary looking clear and glossy through gravel season and salt season.
Not sure how yours is holding up? Bring it by, and we’ll take a look. Calgary Car Detailing does film inspections and ceramic topcoat applications, and we can handle any other detailing while the car’s here. Just tell us when the film went on, and we’ll check the edges and seams while we’re at it.